Mining Industry · Wear Liners, Chutes & Plant Steel

Steel Plate for Mining

Selecting Steel Plate for Mining depends on type, material, grade or standard, dimensions, application, documents, quantity, and destination.

Request a quote for mining steel plate WhatsApp a coordinator

Price on request · confirmed against the site specification, the named product and the mill certificate

What governs the selection

Specifying site plate so acceptance is unambiguous

Specify with enough detail to make acceptance unambiguous: the component and its wear mechanism, the named product programme or the standard, edition and grade, plate thickness, width and length, the delivery condition, any toughness requirement, surface and edge condition and the fabrication and inspection route.

Service duty — governing basis

Input	Typical basis (verify)	Buyer implication	Evidence / RFQ field
Service duty	The governing duty — sliding abrasion, impact, or structural load — decides the acceptance basis, not a generic "mining plate" description	Names the basis for the whole order; the product or grade family follows from the duty	Component + duty description
Grade / product basis	Abrasion-resistant plate is a named product programme; structural members are named by their structural standard and grade	Fixes hardness, chemistry and thickness dependency; the basis is declared, never implied by the application	Exact product/grade designation + edition where applicable
Hardness and its thickness band	A wear product publishes a hardness range held over a stated thickness band — hardness is not uniform across all thicknesses	Sets wear life and what the product programme actually covers for the liner or chute	Hardness basis + the thickness band it holds over
Toughness / impact	Toughness is a separate property from hardness and is not implied by a hardness figure	Impact-carrying parts need a toughness basis on the order; hardness alone does not establish it	Impact requirement, or stated as not required
Delivery / heat-treatment condition	Quenched, quenched-and-tempered or as-rolled as the named product or specification requires	A separate acceptance field from hardness and from toughness — neither implies the other	Delivery / heat-treatment condition as ordered
Thickness range	The named product programme covers a specific thickness range — outside it the published property does not follow	Confirms the thickness ordered actually sits inside the programme's scope	Nominal thickness + unit
Fabrication / NDT	Bending, welding, cutting and any NDT requirement follow the named product's published guidance and the site's specification	These constrain how the plate may be processed and sit on the order, not in the product name	Bending radius + welding procedure + cutting method

The duty and the site specification govern — a generic "mining plate" description is not a complete specification, and no product equivalence is assumed from this page.

Plate size / unit-weight basis

Dimension / tolerance	Typical basis (verify)	Buyer implication	Evidence / RFQ field
Thickness	Declare the exact nominal thickness; a wear product's hardness range and mechanical values are thickness-dependent	Sets wear life, mass, bend radius and whether the thickness sits inside the programme's range	Nominal thickness + unit
Width / Length	Per the nesting or the site's cutting plan; liners and chutes often call for specific plate sizes	Determines cut plan, nesting, remnant recovery and the piece count	Width × Length or plate standard size
Tolerance basis	Thickness / flatness tolerance per the declared product or the referenced dimensional specification	Confirms the plate meets fit-up and liner replacement intent	Tolerance basis + edition
Unit weight	From declared density × volume — verify against the mill certificate	Confirms mass for transport and the quotation basis	Quantity in plates and tonnes

Units, tolerance and mass basis must be stated and verified with the mill / gauge record — computed from density, never assumed.

Site plate — hardness, strength & toughness basis

Property	Typical basis (verify)	Buyer implication	Evidence / RFQ field
Hardness (where applicable)	An abrasion-resistant product programme publishes a hardness range held over a stated thickness band — verify the range and the band it applies to	Hardness speaks to wear rate in sliding abrasion, and is verified against the mill certificate for the thickness ordered	Hardness basis + thickness + test record
Tensile / yield	A tensile band tied to the named grade — verify per the product programme or standard and edition	Confirms the load path for structural and load-bearing site members	Grade + thickness + test record
Elongation	Elongation minimum per the declared grade and thickness	Confirms the plate holds form through forming and welding without cracking	Grade + thickness + elongation record
Impact / toughness	A separate requirement where the part carries impact — not implied by a hardness figure	Toughness governs resistance to cracking under impact and at low temperature, and is evidenced by test rather than inferred	Impact basis + test temperature where required

Hardness, the thickness band it holds over, delivery condition and toughness are separate acceptance criteria — carry each into the RFQ for verification against the mill certificate.

Steel Plate for Mining procurement scene showing plate inspection — Plate edge, surface and identification marks prepared for inspection

Related standards & resources

ASTM A572 high-strength structural plate ASTM A387 chromium-molybdenum alloy plate ASTM A516 pressure vessel plate All steel plate types

Quality, testing & documentation

What gets verified on site plate

Verification follows the purchase specification. Ask for the documents and test records the site specification requires, and match material identification to the ordered basis, dimensions and condition. Certificates, approvals, origin statements and special tests must be confirmed for the actual supply — they are not assumed from this page.

Chemistry and the hardness or mechanical results are held against the ordered basis and the thickness band — not assumed from the application or from a familiar figure.
The impact result, where the component requires one, and the delivery condition are evidenced on their own — a hardness figure implies neither.
Dimensional, flatness, surface and edge checks, any third-party or witnessed inspection, and the forming, welding and NDT records the specification calls for are requested explicitly — never an unsupported certificate.

Steel Plate for Mining procurement scene showing fabrication planning — Cut layout, welding notes and shipment tagging prepared for hand-off

Document & inspection matrix

Product evidence

Mill Test Certificate — chemistry and hardness or mechanical results against the ordered basis
Product programme or grade, edition and delivery condition stated on the certificate
Heat / lot traceability with plate identification marks

Inspection records

Dimensional, flatness, surface and edge inspection per the agreed route
Hardness and/or mechanical (yield / tensile / elongation) test record
Impact test record where the part carries impact

Fabrication & destination documents

Welding, forming and any NDT records the specification requires
Commercial invoice and packing list
Origin / transport documents per the Incoterm

Specification Gate

Steel Plate for Mining specification gate

Compare the details that actually change a purchase: the governing specification, product or grade and condition, hardness and the thickness band it holds over, dimensions, component duty, fabrication route, inspection documents, quantity and destination. Missing inputs are flagged before an RFQ is prepared so an apparently similar option is not treated as equivalent.

RFQ summary

0/6

Add missing fields

Product / grade basis *

Grade *

Component *

Service duty

Delivery / heat-treatment condition

Thickness *

Width

Length

Quantity *

Hardness / toughness basis

Inspection / testing

Fabrication / processing

MTC / certificate / document set

Destination *

Incoterm

Required date

Notes

Fit summary

Insufficient evidence. Still open: Product / grade basis, Grade, Component, Thickness, Quantity, Destination. These stay visibly unresolved rather than being assumed.

No grade or product basis is named. Mining plate selection follows the component's duty and the site specification, and the product or grade programme is declared on the order — a generic "mining plate" description is not a complete specification.
The toughness basis is unresolved. Impact tolerance is a separate property from hardness and is not established by a hardness figure — where the component carries impact, the requirement must be confirmed with the site engineer before the plate is quoted on a comparable basis.
Thickness is not yet stated. Hardness ranges and mechanical values are thickness-dependent, so the thickness band is needed before either requirement can be verified.

Comparison routes are offered once the product basis and the hardness or toughness basis are set — the page will point to the closer product or standard rather than assuming equivalence.

How this gate works

Compliance is scored from the component and its wear mechanism, the named product or grade, the thickness band the hardness holds over, the toughness requirement, the delivery condition and the fabrication and inspection route you supply — not from a generic plate label. Result is Fit for technical review, Comparison needed, or Insufficient evidence. Price on request; availability, lead time and any inspection or document add-ons are confirmed with your quotation, never invented upfront.

Your RFQ summary is sent to the commercial coordinator; a quote follows on your details.

Fit, alternatives & selection logic

Mapping the site requirement to a plate

Start with the service requirement, then narrow by material family, governing specification, product or class, delivery condition and dimensional range. A candidate is suitable only when those order details align with the component's requirement — related products are comparison paths, not automatic substitutes.

Component and wear mechanism

Start from the part and how the material attacks it: a chute liner sees sliding abrasion, a crusher feed area sees a combination of abrasion and impact, and a plant structure carries load. The wear mechanism decides the acceptance basis, so it is identified before a product is named.

Hardness held over a thickness band

A wear plate's published hardness is a range that holds over a stated thickness band, not a figure at any thickness. Both are stated together on the order, because a hardness figure quoted outside its band does not describe the plate being bought.

Product programme vs structural grade

Abrasion-resistant plate is sold as a named product programme, while a structural member is named by its structural standard and grade. The two are different acceptance bases, and the order declares which one governs rather than leaving it to the word "mining".

Toughness and fabrication limits

Impact-carrying parts need a toughness basis stated separately from hardness. The named product's published bending, welding and cutting guidance then constrains how the plate may be formed — and those rules sit on the enquiry rather than being discovered in the workshop.

S355JR structural steel plate

A higher European structural strength tier — where the component carries load rather than resisting abrasion.

Compare S355JR structural steel plate

ASTM A516 Grade 65 plate

A carbon pressure-vessel grade — where the duty is pressure-retaining rather than wear.

Compare ASTM A516 Grade 65 plate

Mining & wear plate

The application route for wear-facing plate, where the abrasion duty and the named product programme are worked through in more detail.

Explore Mining & wear plate

Storage tanks

Site containment and process tanks: check whether the duty requires a tank- or pressure-specific material standard rather than a wear or structural plate.

Explore Storage tanks

Bridge & structural steel

Where the component is a fixed structure rather than a wear part: the same discipline of matching grade, toughness, thickness dependency and documentation to the design.

Explore Bridge & structural steel

Steel Plate for Mining procurement scene showing specification review — Marked plate documentation, calipers and a dimension sketch narrow the specification before the RFQ is sent

Material basis

What defines a Steel Plate for Mining

A mining plate is chosen for what the component has to survive — abrasion, impact or load — and the properties behind that choice are verified against the mill certificate, never assumed from a product name or from another component's plate.

What a wear plate is bought for

Mining plate is chosen for what the component has to survive: sliding abrasion, repeated impact, structural load, or a combination of them. A wear-facing plate is bought for a hardness range held over a stated thickness band, while a structural member is bought for a strength tier. Because those are different acceptance bases, the product or grade is declared on the order rather than assumed from the application, and the actual chemistry and results are verified on the mill certificate for the plate shipped.

RFQ field: the hardness, mechanical or toughness requirement is written into the MTC / certificate request and verified against the plate actually shipped, at the thickness ordered.

Why hardness alone does not settle the order

A hardness figure describes wear resistance, not impact tolerance, and it is published as a range that holds over a specific thickness band — so the same product name can behave differently outside that band. Abrasion-resistant designations are also brand-specific programmes rather than a universal interchange standard, so one supplier's designation is not automatically another's. The hardness basis, the thickness band, the delivery condition, the toughness requirement and the fabrication rules are therefore separate order fields, each verified on its own evidence before the plate reaches the site.

RFQ field: the hardness, mechanical or toughness requirement is written into the MTC / certificate request and verified against the plate actually shipped, at the thickness ordered.

Equivalents

Comparing site plate on evidence, not a familiar figure

A related alternative is comparable only when the governing requirements have been compared and verified. No absolute product-superiority claim is made — each difference is a decision the buyer and the workshop reconcile to the component's requirement.

Comparable plate for the same duty

Another product or grade is comparable only when its hardness or strength basis, the thickness band that basis holds over, delivery condition, toughness, tolerance basis, fabrication guidance and documentation scope have been compared against the component's requirement. Every difference is verified against the mill certificate and the site specification — a similar headline figure does not establish equivalence on its own.

Buyer implication: place this into the RFQ as an explicit comparison basis before any substitution is accepted.

When substitution must be verified

Abrasion-resistant products are named programmes with their own published scope, so a substitution is confirmed against the site's and the workshop's requirements rather than by matching two product names. The same discipline applies across product forms: a plate description that reads alike can still differ in acceptance basis, so the substitution is recorded on the order before it is accepted.

Buyer implication: place this into the RFQ as an explicit comparison basis before any substitution is accepted.

Related specification and standard routes

Follow a related link only when it answers a real specification decision — a neighbouring page is not evidence that two materials are interchangeable.

ASTM A572 high-strength structural plate

A structural grade — where the component carries load and the wear surface is handled separately.

Compare ASTM A572 high-strength structural plate

ASTM A516 pressure vessel plate

A carbon pressure-retaining grade — where the equipment contains pressure rather than wear.

Compare ASTM A516 pressure vessel plate

ASTM A387 chromium-molybdenum plate

An alloy route specified for elevated-temperature service — where the allowable at temperature governs rather than wear resistance.

Compare ASTM A387 chromium-molybdenum plate

All steel plate types

Compare the plate product forms side by side, keeping the acceptance basis consistent across the enquiry.

Compare All steel plate types

MTC requirements

Mill Test Certificate & document evidence for site plate

The MTC ties the chemistry and the hardness or mechanical results to the plate actually shipped, with the product programme or grade, delivery condition and heat / lot traceability recorded. Every document is requested against the ordered basis — never an unsupported certificate.

Mill Test Certificate traceability

The MTC ties the chemistry and the hardness or mechanical results to the plate actually shipped, with the product programme or grade, delivery condition, heat number and lot traceability recorded. For mining wear plate it is requested together with the hardness or mechanical test record and any impact result the component requires — never an unsupported certificate, and never a result carried over from another thickness.

RFQ field: state the MTC, the ordered product and grade, the delivery condition, heat / lot traceability, the hardness and mechanical test records, any impact result and the forming or welding records the specification requires, so the document set matches the plate shipped.

Inspection, fabrication and document set

Dimensional, flatness, surface, edge, hardness, mechanical-test, impact and any third-party or witnessed inspection are requested explicitly, alongside the forming, welding and NDT records the specification calls for and the commercial, origin and transport documents for the destination. Every document is quotation-dependent and stated before acceptance rather than assumed from this page.

Advantages

How the mining plate decision gets safer

A well-qualified enquiry reduces rework at three points: material selection, document review and fabrication hand-off. The practical gain is not a generic promise of superiority — it is a clearer comparison between compliant offers, earlier visibility of missing requirements and a more complete RFQ for technical review.

Risk

Generic "mining plate" description

The RFQ forces the component, duty, product or grade basis and thickness before any value is shown, matching the site's acceptance basis.

A Steel Plate for Mining whose product basis, thickness band and duty are unconditional, auditable ordering inputs.

Risk

Hardness quoted without its thickness band

Hardness is captured together with the band it holds over, since a published range applies to a stated thickness rather than to the product at any thickness.

A wear basis that describes the plate actually being bought.

Risk

Hardness treated as covering impact

Toughness is a separate explicit field wherever the component carries impact, because a hardness figure does not describe impact tolerance.

A plate whose wear basis and impact basis are each stated and tested rather than conflated.

Risk

Product programmes assumed interchangeable

The named product or grade programme and its published scope are declaration fields, so two alike-sounding designations are compared on evidence.

A substitution that is recorded on the order instead of discovered at the workshop.

Risk

Fabrication rules missed until the workshop

Bending radius, welding procedure and cutting method are explicit RFQ fields, requested against the named product's published guidance.

A plate and document set that satisfy the forming and welding route the component actually requires.

Risk

Unsupported stock or lead-time claims

Every stock, price, origin or delivery claim is either verified or left to the RFQ to confirm against the mill and destination process.

A quotation that states delivery, inspection and import expectations rather than hiding them.

Journey

From a site requirement to a documented consignment

Seven checkpoints carry the enquiry from a requirement to a confirmed, documented delivery — each with the responsible owner and the input the RFQ expects. At each step, unresolved requirements stay open rather than being replaced by assumptions.

Requirement
Site / buyer
In: Component, wear mechanism, product or grade basis, thickness and the band the hardness holds over, width, length, quantity and any toughness requirement.
Out: Plate basis stated; duty and material route identified.
No product basis, duty or thickness band named.
Next: Name the product basis and the duty.
Destination & importer
Buyer + commercial
In: Destination, port or site workshop, importer/consignee details.
Out: Destination and clearance owner explicit.
Importer not confirmed.
Next: Add importer/consignee inputs.
Documents & Incoterm
Buyer + commercial
In: Inspection-document needs, forming / welding / NDT records, Incoterm + named place.
Out: Document set and delivery terms stated.
Customs or inspection assumptions unstated.
Next: Confirm document checklist.
Quotation
Commercial
In: Quantity, Incoterm, destination, date.
Out: Availability and pricing on request.
Unknown lead time.
Next: Receive confirmed offer.
Inspection & documents
Technical / QA
In: Chemistry, hardness, mechanical, condition and dimensional checks against the ordered basis.
Out: Product basis, condition, thickness and mass reconciled to the mill ticket and test record.
Missing condition statement, hardness band or test report.
Next: Approve document set.
Packing & shipping
Supplier / forwarder
In: Strapping, marking, Incoterm, port.
Out: Coordinated to the destination.
Document delay.
Next: Track to delivery location.
Delivery & follow-up
Commercial
In: Workshop handover, closed-out docs.
Out: Handed to the site workshop with documents.
Open claims.
Next: Close out.

FAQ

Mining steel plate questions

Straight answers to the questions maintenance engineers, contractors and procurement teams ask most. Each answer depends on the site specification and the actual order conditions.

Which standard or product grade should be stated on an RFQ for mining steel plate?

State the component, the duty it performs, and the product or grade basis the site specification names — together with the thickness, width, length, quantity and any testing requirement. An abrasion-resistant plate is bought as a named product with its own published programme, while a structural member is named by its standard and grade. Because those are different acceptance bases, the description is declared on the order so the quotation and the mill certificate can be matched against the plate actually shipped.

Why does hardness need to be quoted with a thickness band?

A wear product programme publishes a hardness range that holds over a stated thickness band, rather than a figure that applies to the product at any thickness. That means the same product name can behave differently outside the band it was published for. The thickness and the hardness basis are therefore stated together on the enquiry, so the wear basis being quoted describes the plate actually being bought rather than a headline figure taken out of context.

When does toughness matter rather than hardness?

Hardness speaks to wear rate where the governing duty is sliding abrasion. Toughness is a separate property and is not implied by a hardness figure, so where the component carries impact — a crusher feed area, a transfer point with lump material, or a part exposed to low temperature — the toughness requirement is stated on the order and evidenced by test. Which of the two governs follows from the wear mechanism at the part, and both are verified on the mill certificate rather than assumed from the product name.

Can one abrasion-resistant designation be substituted for another?

Abrasion-resistant plate is sold as a named product programme rather than as a universal interchange standard, so one supplier's designation is not automatically another's. A substitution is comparable only when the hardness range, the thickness band it holds over, the delivery condition, toughness, tolerance basis, fabrication guidance and documentation scope have all been compared against the component's requirement. The discipline carries across product forms as well, so any substitution is confirmed against the site specification and recorded on the order before it is accepted.

Which dimensions and documents should be requested, and what does the destination change?

Confirm the nominal thickness, width, length and quantity in plates and tonnes, plus the thickness and flatness tolerance basis and one coherent unit system, since hardness ranges and mechanical values are thickness-dependent and liners and chutes often call for specific sizes. Request the Mill Test Certificate with chemistry and hardness or mechanical results against the ordered basis, the product programme and condition statement, heat and lot traceability, any impact result, and the dimensional and gauge record. For the commercial offer, the destination country, delivery port or site workshop, Incoterm and named place, packing requirements and required delivery date all change the quotation and document set.

Qualified RFQ

Request a qualified mining steel plate quote

Provide the product programme or grade, or the component and the duty it performs, together with thickness, width, length, quantity, destination, required documents and any cutting, forming, testing or inspection scope. If a requirement is still undecided, state it explicitly so the technical review can identify what must be resolved before a commercial offer is finalised.

Request a Quote WhatsApp a coordinator

Price on request · availability and lead time confirmed with your quotation

Applications

Mining plate, mapped alongside related service duties

Application fit depends on what the plate will do in service and how it will be fabricated. Use these paths only where the duty matches — the same nominal plate description can require different hardness, toughness, weldability, corrosion, wear or documentation controls.

Mining & wear plate

The application route for wear-facing plate, where the abrasion duty and the named product programme are worked through in more detail.

Explore Mining & wear plate

Storage tanks

Site containment and process tanks: check whether the duty requires a tank- or pressure-specific material standard rather than a wear or structural plate.

Explore Storage tanks

Bridge & structural steel

Where the component is a fixed structure rather than a wear part: the same discipline of matching grade, toughness, thickness dependency and documentation to the design.

Explore Bridge & structural steel

GCC markets

GCC procurement for mining steel plate

For GCC procurement, keep the technical specification unchanged while checking the destination-specific import path, consignee requirements and shipment documents. Customs, conformity and duty treatment must be confirmed for the actual shipment.

United Arab Emirates

Destination and import documentation.

Carry the wear or structural plate basis, the hardness range and thickness band, and the required document set into the RFQ so the quotation matches the UAE requirement for the declared mining scope.

United Arab Emirates

Saudi Arabia

Project specification and import documentation.

Confirm the grade or product programme, thickness band, dimensions, quantity and delivery window so the plate estimate and logistics stay aligned to the order and the governing site specification.

Saudi Arabia

Qatar

Specification and delivery inputs.

State the wear or structural basis, hardness or toughness requirement, thickness, width, length, quantity, documents and delivery base so the Qatar quotation is fixed on a verified testing basis.

Qatar

Oman

Port-oriented supply for quarry and plant projects.

Oman projects are typically supplied through port destinations, harmonising the plate specification with the site's fabrication, inspection and documentation requirements.

Oman

Kuwait

Contractor procurement and workshop hand-off.

Link plate selection and any cutting, forming or edge preparation to the fabrication, welding and inspection needs, with shipment agreed against the destination and delivery window.

Kuwait

Bahrain

Industrial supply and re-export coordination.

Coordinate material and testing documentation to the delivery requirement so the plate and its document set stay aligned.

Bahrain

Logistics & Incoterm

Commercial comparison after the technical basis is aligned

Quote requests should identify quantity, plate dimensions, destination, required delivery term, inspection and document package and any processing scope. Price, stock and lead time must be confirmed for the live enquiry rather than inferred from a catalogue page.

Packing

Plates stacked, strapped and marked by size, grade, heat and lot, matched to the declared route and destination. Confirm packing and marking requirements in the RFQ.

Delivery route

Name the destination, port or site workshop. Delivery terms are matched to the route and stated on the quotation rather than quoted from a catalogue page.

Incoterm & named place

State the Incoterm and named place so packing, transport and document obligations are explicit and auditable for the plate import.

References

Related pages and technical resources

Verify a closer grade, standard, material, application or technical guide before requesting a quote, keeping the acceptance basis consistent across the enquiry.

Steel plate hub

The parent steel plate range, where the grade and the fabrication intent can be matched across the product forms.

Explore Steel plate hub

Steel plate types

The product-form index, where the plate types can be compared against the duty the component actually sees.

Explore Steel plate types

Steel plate grades

The grade index, where the wear, structural and pressure-vessel families can be read side by side.

Explore Steel plate grades

Thickness tolerance

Review how the thickness and flatness tolerance basis changes acceptance for liner and chute fabrication.

Explore Thickness tolerance

Expert insight

Reading the mining plate requirement before you order

The safest purchasing sequence for Steel Plate for Mining is to identify the governing service requirement first, then lock the material specification and edition, grade or class, delivery condition, dimensions, testing and documents. That sequence avoids comparing offers that share a familiar name but differ in acceptance basis or fabrication risk.

What governs the choice

Mining plate is governed by what the component must survive. Where the duty is sliding abrasion, a wear product is bought for a hardness range — and that range is published for a stated thickness band rather than for the product at any thickness. Where the duty includes impact, toughness is a separate property that a hardness figure does not describe, so the requirement is stated independently and tested. Where the component carries load, the governing property is a strength tier that falls with thickness. Abrasion-resistant designations are also named product programmes rather than a universal interchange standard, and each publishes its own bending, welding and cutting rules. Duty, product basis, thickness band, condition, toughness and fabrication route are therefore separate order fields, each verified on its own evidence.

As a steel trading house we do not guarantee that a named product programme or standard applies to every case, and we make no claim about equipment approvals or product equivalence — the programme, thickness band, condition and any toughness or fabrication requirement are reconciled to the site specification before an order.

Expert perspective on mining plate procurement

Start from the wear mechanism. Sliding abrasion, impact and load are three different acceptance bases, and the mechanism at the part — not the word "mining" — decides which one governs the plate.
Pair hardness with its thickness band. A wear programme publishes a hardness range for a stated thickness band. State the thickness, so the wear basis is checked against what the product actually covers.
Treat toughness as its own field. Impact-carrying parts need a toughness basis on the order. A hardness figure does not establish it, however familiar the product name.
Check the fabrication rules before the first cut. Bending radius, forming direction, welding and cutting guidance are published per product and constrain how the plate may be processed — so they belong on the enquiry.

Working frame: SSAB — Hardox 500 product information · Information date 2026-10-06 · Price on request.