EN 10028 · Flat Products for Pressure Purposes

EN 10028 Pressure Vessel Plate

The EN 10028 Pressure Vessel Plate decision must be matched to the standard scope, grade, dimensions, service conditions, testing, and verifiable documents.

Price on request · confirmed against the part, grade, delivery condition and the inspection documents

Standard scope, parts & dimensions

What EN 10028 covers, and what the order must fix

Specify with enough detail to make acceptance unambiguous: the part and edition, the grade, the delivery condition, plate thickness, width and length, the impact requirement, surface and edge condition and the document type. The standard sets the property basis; the part, grade and condition are decisions the design code and the order fix.

EN 10028 — part, grade & condition basis
InputTypical basis (verify)Buyer implicationEvidence / RFQ field
Series and partEN 10028 — flat products for pressure purposes — is published in parts; the part that applies follows from the property the design depends on, not from the product name (elevated-temperature properties, low-temperature toughness, fine grain, thermomechanically rolled, quenched and tempered, or stainless)The part is a project decision tied to the design code: two different parts are not interchangeable, and a plate ordered only as "EN 10028" is not a complete specificationExact part + standard edition
GradeWithin the applicable part, the grade fixes the strength level and the property set — the design code names the grade the vessel is designed againstNames what the mill certificate is matched against; the grade is not implied by the part aloneExact grade (as named by the design code)
Delivery conditionNormalised, thermomechanically rolled and quenched-and-tempered plate are different products with different property bases; the condition is stated on the order and on the certificateThe delivery condition is a separate field from the impact requirement and from the grade — it describes how the steel was produced and heat-treatedDelivery condition as ordered
Impact / notch toughnessThe impact test temperature and energy level are stated explicitly and are separate from the delivery conditionLow-temperature toughness is the governing property for some parts and grades, and must be named and tested rather than inferred from the conditionImpact test temperature + energy requirement
Elevated-temperature propertiesWhere the design relies on proof strength at temperature rather than at room temperature, the design temperature drives the selectionDesign at temperature is a code calculation — the plate is ordered against the grade and condition the calculation assumesDesign temperature + applicable design code
Testing and documentationInspection documents are issued to the type named on the order, commonly specified to EN 10204; pressure equipment frequently calls for a 3.1 certificateThe certificate type and any third-party inspection are order-specific inputs, not defaultsDocument type + third-party inspection requirement

The part cannot be chosen from the product name, and the delivery condition never implies a stated impact result — both are separate order inputs.

Plate size / unit-weight basis
Dimension / toleranceTypical basis (verify)Buyer implicationEvidence / RFQ field
ThicknessPermitted thickness ranges vary by part and grade — declare exact thickness and confirm the grade's available rangeSets mass, tolerance, property limits and whether the ordered grade is obtainable at that thicknessNominal thickness + unit
Width / LengthPer declared blank or customer sizeDetermines cut plan, nesting, packing and the piece countWidth × Length or plate standard size
Tolerance basisThickness / flatness tolerance per the declared standard or the referenced dimensional specification; a specific tolerance class is a separate ordering inputConfirms the plate meets the fit-up intent for pressure-equipment fabricationTolerance basis / class + edition
Unit weightFrom declared density × volume — verify against MTCConfirms mass for transport and the quotation basisQuantity in plates and tonnes

Units, tolerance and mass basis must be stated and verified with the inspection documents — computed from density, never assumed.

EN 10028 — property & condition basis
PropertyTypical basis (verify)Buyer implicationEvidence / RFQ field
Room-temperature strengthTensile and yield requirements follow from the grade and part and fall with thickness — verify per the edition and the grade orderedConfirms the room-temperature basis the mill certificate is issued againstPart + grade + thickness + test record
Elevated-temperature proof strengthWhere the design relies on behaviour at temperature, the applicable values come from the design code for the grade and temperature in questionDesign at temperature is a code calculation, not a figure to be read from this pageDesign code + design temperature + grade
Impact / notch toughnessThe impact test temperature and energy are stated on the order and are separate from the delivery conditionToughness is a tested acceptance criterion for the parts and grades where low-temperature service applies — never inferred from the condition or the grade nameImpact temperature + energy + specimen orientation
Delivery conditionThe condition as supplied (normalised, thermomechanically rolled, quenched and tempered, and so on) is stated on the certificateDetermines how the mechanical results are read and which fabrication route is appropriateDelivery condition as ordered

Delivery condition and impact testing are separate acceptance criteria — carry both into the RFQ for verification against the inspection documents.

EN 10028 Pressure Vessel Plate procurement scene showing plate inspection
Plate edge, surface and identification marks prepared for inspection

Quality, testing & documentation

What gets verified on an EN 10028 plate

Verification follows the purchase specification. Ask for the documents and test records the project requires, and match material identification to the ordered part, grade, dimensions and condition. Certificates, approvals, origin statements and special tests must be confirmed for the actual supply — they are not assumed from this page.

  • Composition and mechanical results are held against the ordered part and grade and the edition named on the order — not assumed from the product name or from a familiar grade figure.
  • The delivery condition is stated on the certificate for the plate shipped and evidenced separately from any impact requirement, because the two are independent acceptance criteria.
  • Dimensional, flatness, surface and edge checks, the mechanical and impact test records, and any third-party or witnessed inspection are requested explicitly — never an unsupported certificate.
EN 10028 Pressure Vessel Plate procurement scene showing fabrication planning
Cut layout, welding notes and shipment tagging prepared for hand-off

Document & inspection matrix

Product evidence

  • Inspection documents to the type named on the order (commonly EN 10204 3.1 for pressure equipment)
  • Part, grade and delivery condition stated on the certificate for the plate shipped
  • Heat / lot traceability and plate identification to the shipped consignment

Inspection records

  • Dimensional, surface or edge inspection per the agreed route
  • Mechanical test record against the ordered part and grade
  • Impact test record where the order specifies a toughness requirement

Destination documents

  • Commercial invoice and packing list
  • Origin / transport documents per the Incoterm
  • Customs declaration inputs for the destination

Specification Gate

EN 10028 pressure vessel plate specification gate

Compare the details that actually change a purchase: the part and edition, grade, delivery condition, thickness and dimensions, service duty, fabrication route, inspection documents, quantity and destination. Missing inputs are flagged before an RFQ is prepared so an apparently similar option is not treated as equivalent.

RFQ summary

0/7
Add missing fields
EN 10028 part *
Grade *
Delivery condition *
Product form *
Thickness *
Width
Length
Quantity *
Application / service
Design temperature basis
Impact / toughness basis
Inspection document type
Welding / fabrication / processing
Destination *
Incoterm
Required date
Notes

Fit summary

Insufficient evidence. Still open: EN 10028 part, Grade, Delivery condition, Product form, Thickness, Quantity, Destination. These stay visibly unresolved rather than being assumed.
  • No EN 10028 part is named. The part fixes the property set the vessel is designed against, so it cannot be chosen from the product name — confirm it against the design code and the design pressure and temperature before the enquiry is issued.
  • The delivery condition is not stated. Normalised, thermomechanically rolled and quenched-and-tempered plate are different products with different property bases, and the condition is a separate field from the impact requirement.
  • Thickness is not yet stated. Permitted thickness ranges vary by part and grade, so the ordered thickness must be confirmed as available in the grade named before the mechanical requirement can be checked.

Comparison routes are offered once the part and delivery condition are set — the page will point to the closer specification rather than assuming equivalence.

How this gate works

Compliance is scored from the controlling source (the EN 10028 series), the part, the grade, the delivery condition and the impact requirement you supply — not from the product name alone, with the condition and the impact requirement treated as separate controlling inputs. Result is Fit for technical review, Comparison needed, or Insufficient evidence. Price on request; availability, lead time and any inspection or document add-ons are confirmed with your quotation, never invented upfront.

Your RFQ summary is sent to the commercial coordinator; a quote follows on your details.

Fit, alternatives & selection logic

Narrowing the EN 10028 specification

Start with the service requirement, then narrow by material family, governing specification, part, grade, delivery condition and dimensional range. A candidate is suitable only when those order details align with the project requirement — related specifications are comparison paths, not automatic substitutes.

Type and material

EN 10028 covers flat products for pressure purposes. Start from the service: the design code, the design pressure and the design temperature determine which part of the series and which grade the vessel is designed against.

Part, grade and condition

The part fixes the property set, the grade fixes the strength and toughness level, and the delivery condition describes how the steel is produced and heat-treated. All three are separate fields on the RFQ — a plate ordered as "EN 10028" alone is not a complete specification.

Dimensions and tolerances

Thickness, width, length and the tolerance basis fix the plate, its unit weight and the property limits it is accepted against. Permitted thickness ranges vary by part and grade, so confirm the ordered thickness is available in the grade named.

Testing, documentation and fabrication

The impact requirement, the EN 10204 certificate type and any third-party inspection sit on the order. So do welding procedure, heat-treatment controls and NDT for the finished equipment — stated explicitly, never assumed from the standard.

EN 10028 Pressure Vessel Plate procurement scene showing specification review
Marked plate documentation, calipers and a dimension sketch narrow the specification before the RFQ is sent

Composition

What defines an EN 10028 plate

Composition is a purchasing input, not a slogan. Each part of the series carries its own composition rules and its own permitted grades, and the composition for the ordered grade is verified against the inspection documents — never assumed from the product name.

What the part actually fixes

Each part of EN 10028 carries its own composition rules and its own permitted grades — from the non-alloy and alloy steels with specified elevated-temperature properties, through the weldable fine grain steels, to the nickel alloy grades for low-temperature service and the stainless part. The composition for the ordered grade is verified against the certificate, and the part is what tells you which rules apply.

RFQ field: the composition requirement is written into the document request and verified against the plate actually shipped.

Why it changes the purchase

The part, grade, delivery condition and impact requirement are four separate decisions that a single product name hides. Two offers that both read "EN 10028 pressure vessel plate" can differ in every one of them, so the composition, the condition and the toughness basis are each carried as their own RFQ field and verified on their own evidence before the plate is accepted into fabrication.

RFQ field: the composition requirement is written into the document request and verified against the plate actually shipped.

Equivalents

Comparing EN 10028 on evidence, not a similar figure

A related alternative is comparable only when the governing requirements have been compared and verified. No absolute product-superiority claim is made — each difference is a decision the buyer, the design authority and the coordinator reconcile to the pressure service.

Comparable pressure-vessel specification

Another pressure-equipment specification is comparable only when its part or grade, property set, delivery condition, thickness dependency, toughness requirement and document basis match the intended service. Every difference is verified against the certificate and the governing design code.

Buyer implication: place this into the RFQ as an explicit comparison basis before any substitution is accepted.

When substitution must be verified

Do not present a different specification — including an ASTM pressure-vessel standard or the EN 10025 structural series — as equivalent to an EN 10028 part from a similar grade figure alone. They are issued by different bodies with their own designations, property limits and acceptance requirements. A substitution is confirmed by the design authority against the code, not by a supplier's comparison.

Buyer implication: place this into the RFQ as an explicit comparison basis before any substitution is accepted.

Documentation

Inspection documents for EN 10028 pressure plate

The inspection documents tie the composition and mechanical results to the plate actually shipped, with the part, grade and delivery condition stated. Every document is requested against the ordered basis — never an unsupported certificate.

Inspection document traceability

The inspection documents tie the composition and mechanical results to the plate actually shipped, with the part, grade and delivery condition stated and heat / lot traceability recorded. For pressure equipment these are normally issued to EN 10204 at the type named on the order, commonly 3.1 — never an unsupported certificate.

RFQ field: state the document type to EN 10204, the ordered part and grade, the delivery condition, the impact requirement and any third-party inspection in the RFQ so the document set matches the plate shipped.

Inspection & document set

Dimensional, flatness, surface, edge, mechanical-test, impact and any third-party or witnessed inspection are requested explicitly, alongside the commercial, origin and transport documents for the destination. Every document is quotation-dependent and stated before acceptance.

RFQ field: state the document type to EN 10204, the ordered part and grade, the delivery condition, the impact requirement and any third-party inspection in the RFQ so the document set matches the plate shipped.

Advantages

How the EN 10028 decision gets safer

A well-qualified enquiry reduces rework at three points: material selection, document review and fabrication hand-off. The practical gain is not a generic promise of superiority — it is a clearer comparison between compliant offers, earlier visibility of missing requirements and a more complete RFQ for technical review.

01

Risk

Part or grade left unnamed

The RFQ forces the EN 10028 part, the grade and the delivery condition before any value is shown, matching the design code the vessel is designed against.

An EN 10028 plate whose part, grade, condition and thickness are unconditional, auditable ordering inputs.
02

Risk

Delivery condition confused with impact testing

The delivery condition and the impact requirement are separate RFQ fields, because one describes how the steel is produced and the other what it must demonstrate at a stated temperature.

A plate whose condition and toughness basis are each stated and evidenced on their own.
03

Risk

Composition and mechanical values unchecked

Composition, mechanical-test, impact and traceability needs are explicit RFQ fields, requested against the ordered part and grade before quotation.

Inspection documents that match the plate actually shipped.
04

Risk

Quotation gaps or hidden assumptions

Application, processing, destination, Incoterm, document type and date are separate explicit fields, never buried in a price.

A quotation that states delivery, certificate and import expectations rather than hiding them.
05

Risk

Unsupported stock or lead-time claims

Every stock, price, origin or delivery claim is either verified or left to the RFQ to confirm against the mill and destination process.

No surprise when availability and lead time are confirmed.

Journey

From an EN 10028 requirement to a documented consignment

Seven checkpoints carry the enquiry from a requirement to a confirmed, documented delivery — each with the responsible owner and the input the RFQ expects. At each step, unresolved requirements stay open rather than being replaced by assumptions.

  1. Requirement

    Buyer / design

    In: Design code, design pressure, design temperature, EN 10028 part, grade, delivery condition, product form, thickness, width, length, quantity and any impact requirement.

    Out: Part, grade and condition basis stated; route and material identified.

    No part, grade or condition named — "EN 10028" alone.

    Next: Name the part, grade and condition.

  2. Destination & importer

    Buyer + commercial

    In: Destination, port or delivery location, importer/consignee details.

    Out: Destination and clearance owner explicit.

    Importer not confirmed.

    Next: Add importer/consignee inputs.

  3. Documents & Incoterm

    Buyer + commercial

    In: EN 10204 document type, third-party inspection needs, Incoterm + named place.

    Out: Document set and delivery terms stated.

    Customs or certificate assumptions unstated.

    Next: Confirm document checklist.

  4. Quotation

    Commercial

    In: Quantity, Incoterm, destination, date.

    Out: Availability and pricing on request.

    Unknown lead time.

    Next: Receive confirmed offer.

  5. Inspection & documents

    Technical / QA

    In: Composition, mechanical, impact, condition and dimensional checks against the ordered part and grade.

    Out: Part, grade, condition, thickness and mass reconciled to the inspection documents and test record.

    Missing condition statement, impact result or certificate type.

    Next: Approve document set.

  6. Packing & shipping

    Supplier / forwarder

    In: Strapping, marking, Incoterm, port.

    Out: Coordinated to the destination.

    Document delay.

    Next: Track to delivery location.

  7. Delivery & follow-up

    Commercial

    In: Site handover, closed-out docs.

    Out: Handed to site with documents.

    Open claims.

    Next: Close out.

FAQ

EN 10028 pressure vessel plate questions

Straight answers to the questions procurement and QA teams ask most. Each answer depends on the project specification and the actual order conditions.

Which part of EN 10028 applies to my pressure vessel, and what should the RFQ state?
State the part, the grade, the delivery condition, the thickness, the design temperature and the inspection documents the project requires, together with the design code the vessel is designed against. The part follows from the property the design depends on — elevated-temperature strength, low-temperature toughness, or the delivery condition the fabrication requires — and is not chosen from the product name. EN 10028 is published in parts, each with its own property basis, permitted grades and testing rules, so the part and grade the design code names are what the quotation and inspection documents are matched against.
How is the delivery condition different from the impact requirement?
They are two separate things. The delivery condition — normalised, normalised and tempered, thermomechanically rolled, quenched and tempered, or as the part provides — describes how the steel was produced and heat-treated, and is stated on the order and on the certificate. The impact requirement sets what the plate must demonstrate at a stated test temperature, with its own energy level and specimen orientation. Because they are independent, one never implies the other: a stated delivery condition does not establish a stated impact result, and both belong on the enquiry as separate fields.
Which dimensions and tolerances govern acceptance?
Confirm nominal thickness, width, length and quantity in plates and tonnes, plus the tolerance basis and any specific tolerance class the fabrication calls for, in one coherent unit system. Permitted thickness ranges and property limits vary by part and grade, so the ordered thickness is confirmed as available in the grade named and reconciled to the inspection documents. State the surface and edge condition and any cut-to-size or edge preparation before quotation.
What inspection documents are issued with EN 10028 pressure plate?
Inspection documents are issued to the type named on the order, commonly specified to EN 10204. Pressure equipment usually calls for a 3.1 certificate, and where a 3.2 certificate or third-party witnessed inspection is required that must be stated at the enquiry stage so it can be scheduled and priced. The part, grade and delivery condition are stated on the certificate for the plate shipped, with heat and lot traceability and the mechanical and impact test records where the order specifies them.
Is EN 10028 equivalent to ASTM A516, and what destination details are needed for a firm offer?
No. They are different specifications issued by different bodies, with their own grade designations, property limits and acceptance requirements. Both serve pressure equipment and a project may reference either, but one is not automatically a substitute for the other — a substitution is confirmed by the design authority against the governing code. For the commercial offer, the destination country, delivery location or port, Incoterm and named place, packing and marking requirements and the required delivery date all change the quotation and document set.

Qualified RFQ

Request a qualified EN 10028 plate quote

Provide the part, grade and delivery condition or the service requirement, thickness, width, length, quantity, destination, required documents and any cutting, testing or inspection scope. If a requirement is still undecided, state it explicitly so the technical review can identify what must be resolved before a commercial offer is finalised.

Price on request · availability and lead time confirmed with your quotation

Applications

EN 10028 plate, mapped to service duty

Application fit depends on what the plate will do in service and how it will be fabricated. Use these paths only where the duty matches — the same nominal plate description can require different toughness, weldability, corrosion, wear or documentation controls.

Pressure vessels

Pressure-retaining service: reconcile the part, grade, delivery condition and impact requirement to the governing design code before the plate basis is fixed.

Explore Pressure vessels

Boilers & elevated-temperature service

Boiler and heat-exchanger service: confirm whether the design relies on elevated-temperature properties and which part and grade that points to.

Explore Boilers & elevated-temperature service

Fabrication

Where the duty is structural rather than pressure-retaining, a structural standard is likely to be the correct basis instead.

Explore Fabrication

GCC markets

GCC procurement for EN 10028 pressure plate

For GCC procurement, keep the technical specification unchanged while checking the destination-specific import path, consignee requirements and shipment documents. Customs, conformity and duty treatment must be confirmed for the actual shipment.

AE flag

United Arab Emirates

Destination and import documentation.

Carry the EN 10028 part, grade, delivery condition and destination emirate into the RFQ so the quotation and document set match the UAE requirement for the declared pressure plate.

United Arab Emirates
SA flag

Saudi Arabia

Project specification and import documentation.

Confirm the part, grade, delivery condition, dimensions, quantity and delivery window so the plate estimate and logistics stay aligned to the order and the governing design code.

Saudi Arabia
QA flag

Qatar

Specification and delivery inputs.

State the EN 10028 part and grade, delivery condition, plate thickness, width, length, quantity, documents and delivery base so the Qatar quotation is fixed on a verified basis.

Qatar
OM flag

Oman

Port-oriented supply for process projects.

Oman projects are typically supplied through port destinations, harmonising the EN 10028 pressure plate specification with the project's fabrication and inspection requirements.

Oman
KW flag

Kuwait

Refinery and process procurement hand-off.

Link plate selection and any cutting or forming to the fabrication, welding and inspection needs, with shipment agreed against the destination and delivery window.

Kuwait
BH flag

Bahrain

Industrial supply and re-export coordination.

Coordinate material, delivery-condition and testing documentation to the delivery requirement so the EN 10028 plate and its document set stay aligned.

Bahrain

Logistics & Incoterm

Commercial comparison after the technical basis is aligned

Quote requests should identify quantity, plate dimensions, destination, required delivery term, inspection/document package and any processing scope. Price, stock and lead time must be confirmed for the live enquiry rather than inferred from a catalogue page.

Packing

Plates stacked, strapped and marked by size, grade, part, heat and lot, matched to the declared route and destination. Confirm packing and marking in the RFQ.

Delivery route

Name the destination, port or delivery location. Delivery terms are matched to the route and stated on the quotation.

Incoterm & named place

State the Incoterm and named place so packing, transport and document obligations are explicit and auditable for the EN 10028 plate import.

Expert insight

Reading the EN 10028 series before you order

The safest purchasing sequence for an EN 10028 pressure vessel plate is to identify the governing service requirement first, then lock the material specification and edition, part, grade, delivery condition, dimensions, testing and documents. That sequence avoids comparing offers that share a familiar name but differ in acceptance basis or fabrication risk.

What the series governs

EN 10028 specifies the technical delivery conditions for flat products of steel for pressure purposes, and it is published in parts divided by property set and delivery condition — from the non-alloy and alloy steels with specified elevated-temperature properties, through the weldable fine grain steels in normalised, thermomechanically rolled and quenched-and-tempered conditions, to the nickel alloy grades for low-temperature service and the stainless part. What a project references is the part and grade its design code names, not the series as a whole. The delivery condition is part of how the material is designated and is stated on the order separately from the impact requirement, because the two are independent.

What the series does not establish is equally important: that a different specification is an automatic substitute, the vessel's design pressure, temperature or corrosion allowance, that a stated delivery condition implies a stated impact result, or project-specific approval. The working frame is the published EN 10028 series.

Expert perspective on EN 10028 procurement

  • Start from the design code. The code and the design pressure and temperature determine the part and grade — the part cannot be chosen from the product name, and asking for "EN 10028 plate" without one is not a complete specification.
  • Keep condition and impact separate. The delivery condition describes how the steel is produced and heat-treated; the impact requirement sets what it must demonstrate at a stated temperature. Neither implies the other.
  • State the document type early. Pressure equipment commonly calls for EN 10204 3.1, and a 3.2 certificate or witnessed inspection has to be declared at enquiry so it can be scheduled and priced.
  • Confirm the substitution route. EN 10028 and other pressure specifications are issued by different bodies; any substitution is confirmed by the design authority against the code rather than by a supplier comparison.
Working frame: BSI Knowledge — EN 10028 series · Information date 2026-10-06 · Price on request.